Material scienceMarch 15, 20268 min read

CUPAL technical datasheet: 70/30 copper-aluminium bimetal sheet

In short

CUPAL® 70/30 is a copper-aluminium bimetal sheet: copper roll-bonded onto aluminium, 70 % aluminium and 30 % copper by layer thickness. Conductivity is 41.9 MS/m (about 72 % IACS) and density 4.6 g/cm³. In the 500 × 500 mm sheet, 0.5 and 1.0 mm are stock items; 1.5 and 2.0 mm are made to order.

41.9MS/m
Conductivity (≈72 % IACS)
4.6g/cm³
Density
0.5–2.0mm
Sheet thickness
500 × 500mm
Stock sheet

This page holds the material data. If your drawing or bill of materials carries a distributor code instead (880111, VCUP2, ICALCU10CS), the CUPAL part number cross-reference maps it to our sizes.

Formats and stock

The base format is a 500 × 500 mm sheet. The 0.5 and 1.0 mm gauges are stock items, delivered 2–10 working days from order. The 1.5 and 2.0 mm gauges are made to order, with 5–10 working days of production. Each SKU links to its row on the CUPAL sheet product page, where you will find the net list price and the quantity selector.

SKUThicknessSheetTheoretical massAvailability
TCUP050.5 mm500 × 500 mm0.58 kgStock
TCUP101.0 mm500 × 500 mm1.15 kgStock
TCUP151.5 mm500 × 500 mm1.73 kgMade to order
TCUP202.0 mm500 × 500 mm2.30 kgMade to order

The larger 500 × 2000 mm sheet is available on request. It has no list price; we quote within 24 hours.

ThicknessSheetTheoretical massAvailability
0.5 mm500 × 2000 mm2.30 kgOn request, quoted
1.0 mm500 × 2000 mm4.60 kgOn request, quoted
1.5 mm500 × 2000 mm6.90 kgOn request, quoted
2.0 mm500 × 2000 mm9.20 kgOn request, quoted

Masses are theoretical: volume × the nominal density of 4.6 g/cm³. A real sheet differs slightly within the thickness tolerance.

The same material also comes as finished parts: CUPAL strip in the standard 500 × 40 × 0.5 mm size, CUPAL washers in 11 sizes from M6 to M20, and CUPAL plates for busbar and terminal joints. If none of them fits the joint, we supply parts cut from the sheet to your drawing. A partner does the cutting; see custom cutting.

Layer build-up per gauge

The 70/30 ratio refers to layer thickness: 30 % of the sheet thickness is copper and 70 % is aluminium. That gives the nominal copper-layer thickness, which is the figure that matters for current rating, deburring and bending.

Sheet thicknessCopper layer (nominal)Aluminium layer (nominal)
0.5 mm0.15 mm0.35 mm
1.0 mm0.30 mm0.70 mm
1.5 mm0.45 mm1.05 mm
2.0 mm0.60 mm1.40 mm

These are nominal values derived from the 70/30 layer ratio. If your specification sets a minimum copper thickness, state it in the enquiry and we will confirm it before you order.

By mass the split is different. With copper at 8.96 g/cm³ and aluminium at 2.70 g/cm³, about 59 % of the sheet's mass is copper: 0.3 × 8.96 / (0.3 × 8.96 + 0.7 × 2.70) = 0.587. The same two layers give a density of 0.3 × 8.96 + 0.7 × 2.70 = 4.58 g/cm³, which matches the 4.6 g/cm³ on this sheet.

Electrical properties

PropertyValueNote
Electrical conductivity41.9 MS/m= 41.9 m/(Ω·mm²)
Conductivity in % IACS≈72 % IACS41.9 / 58.0 = 0.722; 100 % IACS = 58.0 MS/m (annealed copper, IEC 60028)
Resistivity0.0239 Ω·mm²/m= 1 / 41.9
Cross-section for equal conductance vs copper1.41 ×material data
Cross-section for equal conductance vs aluminium0.906 ×material data
Mass for equal conductance vs copper≈71 %(58.0 / 41.9) × (4.6 / 8.96) = 0.71

Against the IACS reference copper (58.0 MS/m) the cross-section ratio is 58.0 / 41.9 = 1.38. The material-data factor of 1.41 is slightly higher, so it is the more conservative value for sizing. Sized for the same conductance, a CUPAL part weighs about 71 % of the copper part, not half. The full comparison with copper and aluminium is in CUPAL, copper or aluminium?.

Physical and mechanical properties

PropertyValueUnit
Density4.6g/cm³
Thermal conductivity265W/(m·K)
Coefficient of linear thermal expansion21.810⁻⁶/K
Modulus of elasticity81kN/mm²
Tensile strength130–180N/mm²
Bond strength between layers70–110N/cm strip width
Tempersoft–

Surface hardness

SideVickersBrinell
Aluminium side30–40 HV 0.230–40 HB 2.5/62.5
Copper side50–70 HV 0.250–70 HB 2.5/62.5

Layer materials

PropertyAluminium layer (carrier)Copper layer (cladding)
GradeAL 99.5E1-Cu58
Material number3.0255 (DIN 17007)2.0065 (DIN 1787)
Other designationEN AW-1050ACU/a1 (NF A 53-100)
Puritymin. 99.5 % AlCu 99.9 %

The copper is cold roll-bonded onto the aluminium and then diffusion-bonded by heat treatment. Our raw material comes from c:met GmbH in Wendelstein, Germany, the CUPAL trademark holder, certified to ISO 9001:2015. HIDRA-MIX Kft. in Budapest sells it in Hungary and the EU.

Surface and edge

FinishDescription
Mill finish (Walzblank)As rolled; the standard finish
Bright (Blank)Bright, reflective finish
Brushed (Gebürstet)Directionally brushed
Satin (Satiniert)Fine satin finish
EDTElectrical discharge textured, non-directional

Edges are as cut (GK). Every cut edge shows the copper-aluminium bond line, where both metals meet the environment. In a dry indoor joint this does not matter. Outdoors or in humid conditions the edge needs to be protected or covered; ask us before you specify such a joint.

Processing

Cold forming: bending, deep drawing, punching, stretch forming, edge bending, profiling, beading, riveting and flanging.

Joining: the copper side can be soft-soldered and electroplated with standard processes. In electrical work CUPAL mostly goes into bolted joints.

Cutting and punching: custom parts are cut by our partner, by laser, punching tool or guillotine shear. Which process pays off when, and what to watch at the bond line, is covered in laser cutting or punching. Order through custom cutting; the smallest order is one 500 × 500 mm sheet of material.

Heat-treatment limit

CUPAL can be heat-treated at no more than 260 °C for no more than 4 hours. This is the limit for annealing and processing (removing the work hardening from cold forming), not a service temperature. Heated longer or hotter, the intermetallic layer at the copper-aluminium interface grows uncontrolled and weakens the bond between the layers.

The permissible operating temperature of a finished joint is set by its components (lug, bolt, insulation) and by the equipment standard. If your project needs a material-side limit, ask us and we will check it with our supplier.

Standards and certificates

ItemReference
Aluminium layerDIN 17007 / Werkstoff-Nr. 3.0255
Copper layerDIN 1787 / Werkstoff-Nr. 2.0065
Material certificateEN 10204 2.2 test report with every delivery; 3.1 inspection certificate on request
Supplier quality managementISO 9001:2015 (c:met GmbH)

Every delivery ships with an EN 10204 2.2 test report; a batch-specific 3.1 inspection certificate is available on request. The EN 10204 material certificate article explains the difference.

CUPAL transition parts usually sit where an aluminium busbar (DIN 43670) meets a copper busbar (DIN 43671) or a copper lug, in switchgear to IEC 61439, cable connections to IEC 61238 or lightning protection to IEC 62305. Those are standards for the equipment and the joint, not for the CUPAL material. They are summarised on the standards page.

Delivery, storage and ordering

We deliver within Hungary and across the EU, DAP within the EU; collection in Budapest is also possible. Store the sheet in a dry, well-ventilated place.

For a quote, send:

  • thickness (0.5 / 1.0 / 1.5 / 2.0 mm);
  • size, or a drawing (DXF or PDF) for custom parts;
  • quantity, plus the expected repeat volume if there is one;
  • whether you need a 3.1 certificate.

We quote within 24 hours. Stock sheet is delivered 2–10 working days from order. Made-to-order gauges and custom cutting take 5–10 working days of production, and a custom order arrives door to door within the EU in 2–4 weeks.

Request a quote: give the thickness and size, or attach the drawing, and we reply within 24 hours.

CUPAL datasheet questions

41.9 MS/m, i.e. 41.9 m/(Ω·mm²), which is about 72 % IACS (41.9 / 58.0, where 100 % IACS is annealed copper at 58.0 MS/m). Resistivity is 0.0239 Ω·mm²/m. For equal conductance, size CUPAL at 1.41 times the copper cross-section.
4.6 g/cm³, which is 51 % of copper's 8.96 g/cm³. Sized for the same conductance, though, a CUPAL part weighs about 71 % of the copper part, because it needs a larger cross-section.
Nominally 0.30 mm, on 0.70 mm of aluminium, because the 70/30 ratio refers to layer thickness. The nominal copper layer is 0.15 mm on 0.5 mm sheet, 0.45 mm on 1.5 mm and 0.60 mm on 2.0 mm. If your specification sets a minimum copper thickness, we confirm it before you order.
3.0255 is the material number of AL 99.5 aluminium (DIN 17007 numbering, EN AW-1050A), the carrier layer of CUPAL. 2.0065 is E1-Cu58 copper to DIN 1787, the clad copper layer.
0.5 mm (TCUP05) and 1.0 mm (TCUP10) in the 500 × 500 mm sheet, delivered 2–10 working days from order. 1.5 mm (TCUP15) and 2.0 mm (TCUP20) are made to order with 5–10 working days of production. The 500 × 2000 mm sheet is supplied on request against a quote.
260 °C for at most 4 hours. That is the limit for annealing and processing, not a service temperature: beyond it, the intermetallic layer at the copper-aluminium interface grows uncontrolled. The operating temperature of a finished joint is set by its components and the equipment standard; we check material-side limits with our supplier on request.
70 % aluminium (AL 99.5, material number 3.0255) and 30 % copper (E1-Cu58, material number 2.0065) by layer thickness, cold roll-bonded and diffusion-bonded. By mass, copper is about 59 % of the sheet.
Tensile strength is 130–180 N/mm², the bond strength between the copper and aluminium layers is 70–110 N/cm of strip width, and the modulus of elasticity is 81 kN/mm². It is supplied soft and suits cold forming.

Have a question?

Email us or use the form: we reply within 24 hours on working days.

Get a Quote