Material scienceFebruary 15, 202611 min read

What is CUPAL? The copper-aluminium (Cu-Al) bimetal, explained

In short

CUPAL® is a copper-aluminium bimetal (Cu-Al): a copper layer roll-bonded onto an aluminium carrier, 70/30 by layer thickness. One face is copper, the other aluminium, so in a bolted joint each conductor touches its own metal and the copper-aluminium interface sits inside the material. Density 4.6 g/cm³, conductivity 41.9 MS/m, about 72 % IACS.

70/30
Al/Cu by layer thickness
4.6g/cm³
Density
41.9MS/m
Conductivity, ≈72 % IACS
500 × 500mm
Stock sheet size

Delivery forms

CUPAL is bought either as material to cut or as a finished part for the joint. We supply all of the forms below from Budapest to Hungary and the rest of the EU. Stock items arrive 2–10 working days after the order.

FormSizesAvailability
CUPAL sheet500 × 500 mm, 0.5 / 1.0 / 1.5 / 2.0 mm0.5 and 1.0 mm from stock, 1.5 and 2.0 mm made to order
CUPAL strip500 × 40 × 0.5 mm, other widths to orderStandard size from stock
CUPAL washersM6–M20, 11 sizes, 16–46 mm outer diameter, 1–2 mm thickFrom stock
Al/Cu cable lugs and connectors10–625 mm², M8–M20 bolt holes, inline connectors, pin lugsFrom stock
CUPAL platesTransition plates for busbar and terminal jointsSee the product page
Parts cut from your drawingDiscs, strips, plates, any contour, cut by our partner5–10 working days production, from one 500 × 500 mm sheet

Prices are on each product page. If you are not sure which form your joint needs, connecting copper to aluminium goes through it joint by joint.

What does CUPAL mean? Cu, Al and Cu/Al

The name joins the chemical symbols Cu (copper) and Al (aluminium). Electrical catalogues use the same pair, written Cu/Al, Cu-Al or Al/Cu, for any part with a copper side and an aluminium side: a bimetal washer, an Al/Cu cable lug, a transition plate.

What Cu-Al does not mean here is an alloy. When copper and aluminium are melted together the result is aluminium bronze, a copper alloy with roughly 5–11 % aluminium. Its standard designations start with CuAl, for example CuAl10Fe3. That is a different material for different jobs. In CUPAL the two metals stay separate layers.

Composition and structure

CUPAL has an aluminium carrier, AL 99.5 (material no. 3.0255, EN AW-1050A), and a copper layer, E1-Cu58 (material no. 2.0065). The 70/30 split refers to layer thickness: a 1.0 mm sheet has nominally 0.70 mm of aluminium and 0.30 mm of copper. By mass the copper share is higher, about 59 %, because copper is more than three times as dense as aluminium (0.3 × 8.96 against 0.7 × 2.70 g/cm³).

The two layers are bonded metallurgically and cannot be peeled apart. The bond strength is 70–110 N per cm of strip width.

PropertyValue
Density4.6 g/cm³
Electrical conductivity41.9 MS/m = m/(Ω·mm²), ≈72 % IACS
Electrical resistivity0.0239 Ω·mm²/m
Tensile strength130–180 N/mm²
Bond strength between the layers70–110 N/cm

Hardness, thermal data, the layer thickness for every gauge and the stock formats are in the CUPAL technical datasheet.

How CUPAL is made

CUPAL is made by roll bonding (cold roll cladding). Prepared copper and aluminium strip pass through a rolling stand together under very high pressure and bond in the solid state. A controlled heat treatment then restores formability and lets the interface diffuse into a firm metallurgical bond. Time and temperature are limited so that only a very thin intermetallic layer forms at the boundary.

The finished sheet can be bent, punched, deep-drawn, riveted and profiled, and the copper face can be soft-soldered or plated. We buy the material from c:met GmbH in Wendelstein, Germany, the CUPAL trademark holder and an ISO 9001:2015-certified supplier.

How CUPAL stops galvanic corrosion at a copper-aluminium joint

Bolt a copper lug straight onto an aluminium busbar and the two metals form a galvanic couple wherever moisture reaches the contact. The aluminium corrodes, contact resistance rises and the joint runs hot. The galvanic corrosion guide explains the mechanism.

A CUPAL washer or plate between the two moves the copper-aluminium boundary into the material. Its copper face sits against the copper part, its aluminium face against the aluminium part, and the boundary between them is closed by the metallurgical bond. Every contact surface in the joint is like on like.

One limit applies to every cut part: at the edge, the bond line is exposed. In a dry indoor panel that does not matter. For outdoor or humid joints, protect or cover the edge and ask us before you specify. The CUPAL installation guide covers orientation, surface preparation and tightening.

CUPAL, copper or aluminium?

CUPAL does not replace copper as a conductor. It is the piece that joins copper to aluminium. Next to the two pure metals the figures look like this:

PropertyCopperCUPAL 70/30Aluminium
Density8.96 g/cm³4.6 g/cm³2.70 g/cm³
Conductivity58.0 MS/m (100 % IACS)41.9 MS/m (≈72 % IACS)≈36 MS/m (≈62 % IACS)
Cross-section for the same conductance1 ×≈1.4 ×≈1.6 ×
Mass for the same conductance100 %≈71 %≈49 %
Contact faces in a Cu-Al bolted jointCopper on aluminiumCopper on copper, aluminium on aluminiumAluminium on copper

Copper is taken at the IACS reference of 58.0 MS/m, aluminium as AL 99.5 at about 36 MS/m. Mass for the same conductance is the cross-section factor times the density ratio; for CUPAL that is (58.0 / 41.9) × (4.6 / 8.96) ≈ 0.71. The material data use a slightly more conservative sizing factor of 1.41 × the copper cross-section, listed in the datasheet.

So a CUPAL conductor with the same conductance as copper is about 29 % lighter, not half the weight. The density is roughly half, but it needs about 1.4 times the cross-section.

JointGalvanic corrosion risk
Copper on copperNone
Aluminium on aluminiumNone
Copper directly on aluminiumHigh, especially where moisture gets in
Copper, CUPAL, aluminiumNone at the contact faces; protect the cut edge outdoors

When to use which:

  • CUPAL wherever a copper part is bolted to an aluminium part: a copper lug on an aluminium busbar, an aluminium busbar on a copper terminal, a copper bonding conductor on an aluminium mast or frame.
  • Copper for copper-to-copper joints and wherever the most conductance per cross-section counts.
  • Aluminium for aluminium-to-aluminium joints and conductors where weight counts.

CUPAL or Cuponal?

The two names sound alike and both describe copper on aluminium, but they are different products from different makers.

Cuponal is a registered trademark of Hydrostatic Extrusions Ltd, based in Perth, Scotland, and part of Bruker Corporation. VDM Engineered Solutions is its exclusive sales partner for the German-speaking countries, the Benelux, France and Taiwan. Cuponal is made by hydrostatic extrusion: a seamless copper cladding is pressure-bonded around an aluminium core. Its makers list it as long products only: busbars, rods, profiles and wire.

CUPAL is roll-bonded sheet with a copper face and an aluminium face, and the parts made from it: washers, strips, plates and parts cut to a drawing.

PropertyCUPALCuponal
FormSheet, and washers, strips and plates made from itBusbars, rods, profiles, wire
ProcessRoll bonding, copper on one faceHydrostatic extrusion, copper all round an aluminium core
Copper share30 % by layer thickness, ≈59 % by mass15 % by volume, 37 % by mass (standard sections)
Conductivity41.9 MS/m, ≈72 % IACS37.7 MS/m, 65 % IACS
Density4.6 g/cm³3.63 g/cm³

Cuponal figures are from the Bruker Cuponal page and the VDM Metals Cuponal brochure.

If a specification calls for a Cuponal busbar profile, that is a different supply chain from ours. If it calls for a copper-aluminium washer, plate, disc or strip, that is CUPAL.

The same material: Cu-Al bimetal, copper-aluminium bimetal sheet, bimetal sheet. Finished parts are named after their shape: bimetallic washer, transition plate, bimetallic connector (the trade name for a part with a different metal on each face). Tell us the conductor cross-section, the bolt size and what it bolts to, and we will say which part you need.

Not the same:

  • CCA in cable catalogues means copper-clad aluminium wire: a thin copper skin around an aluminium conductor, used to save cost. It is a conductor, not a transition element, and it does not solve a bolted copper-to-aluminium joint.
  • Cupro-aluminium is another name for aluminium bronze, the copper alloy described above. It is not a CUPAL synonym.
  • Thermostat bimetal is a strip that bends with temperature. It shares the word "bimetal" and nothing else.
  • Transition washer can mean either a CUPAL bimetal washer or a profiled copper-alloy washer whose ridges pierce the aluminium oxide film. Check which one a specification means: bimetallic or toothed transition washer.

Where CUPAL is used

Which part does your joint need?

A bimetal Al/Cu cable lug carries the transition inside the lug, so it needs no CUPAL washer. A washer is for the other case: a plain copper lug bolted onto an aluminium busbar or terminal. Anything the washer and lug ranges do not cover, such as an odd bore, a larger outer diameter or a busbar transition plate, is cut from sheet to your drawing by our partner.

To get a quote, send the conductor cross-section, the bolt size and what the part bolts to; for a cut part, the thickness, a DXF or PDF drawing and the quantity. You get the quote within 24 hours. Stock items arrive in 2–10 working days, custom parts take 5–10 working days to produce, and a custom order reaches an EU address door to door in 2–4 weeks. Request a quote.

Frequently asked questions about CUPAL

No. CUPAL is a bimetal: a copper layer roll-bonded onto aluminium, where each metal keeps its own properties. A copper-aluminium alloy is aluminium bronze (for example CuAl10Fe3), which is a different material.
The name joins the chemical symbols Cu (copper) and Al (aluminium). It stands for a copper-aluminium bimetal sheet with a copper face and an aluminium face, and for the washers, strips and plates made from it.
70 % aluminium and 30 % copper by layer thickness, so a 1.0 mm sheet has about 0.70 mm aluminium and 0.30 mm copper. By mass the copper share is about 59 %, because copper is much denser than aluminium.
41.9 MS/m, the same as 41.9 m/(Ω·mm²), which is about 72 % IACS (41.9 / 58.0). For the same conductance as copper it needs about 1.4 times the cross-section; the material data give 1.41 as the sizing factor.
Per volume CUPAL weighs about half as much as copper (4.6 against 8.96 g/cm³). For the same conductance it needs about 1.4 times the cross-section, so the part weighs about 71 % of a copper part, roughly 29 % less.
Its copper face touches the copper part and its aluminium face touches the aluminium part, so no contact surface in the joint pairs copper with aluminium. The copper-aluminium boundary is inside the material. At a cut edge that boundary is exposed, so outdoor or humid joints need the edge protected or covered.
We sell CUPAL sheet in 500 × 500 mm boards: 0.5 and 1.0 mm from stock, 1.5 and 2.0 mm made to order, with list prices on the CUPAL sheet page. We ship from Budapest to Hungary and the rest of the EU, and cut parts to your drawing from one board upwards.
No. Cuponal is a copper-clad aluminium long product (busbars, rods, profiles, wire) made by hydrostatic extrusion. CUPAL is roll-bonded sheet and the washers, strips and plates cut from it.
The trade name for a connecting part with a different metal on each face, so that in a bolted joint aluminium meets aluminium and copper meets copper. In CUPAL that means Al/Cu cable lugs for 10–625 mm² with M8–M20 bolt holes, washers from M6 to M20, and plates or discs cut to your drawing.

The vocabulary around CUPAL (bimetal, galvanic corrosion, material number, EN 10204 certificate) is collected with one-line definitions in the CUPAL glossary. The standards that apply to the material and to the joints are on the standards page, and the certificate types are explained in EN 10204 material certificate: 2.2 or 3.1. If you already know the bolt size, the washer size guide helps you pick the outer diameter.

Have a question?

Email us or use the form: we reply within 24 hours on working days.

Get a Quote