Standards and certificates

Standards, material numbers and certificates

CUPAL® material reaches us through the ISO 9001:2015 certified supply chain of c:met GmbH, our supplier and the CUPAL trademark holder. This page lists the material numbers of both layers and the documents you can order with a delivery, and shows which standards cover the material and which the equipment it goes into.

In short

CUPAL copper-aluminium bimetal has two layers: Al 99.5 aluminium (EN AW-1050A, Werkstoff-Nr. 3.0255) and 99.9 % copper (Werkstoff-Nr. 2.0065). An EN 10204 2.2 test report ships with every delivery. Ask in your quote request for a 3.1 inspection certificate, the supplier's ISO 9001 certificate or an SVHC declaration. No material can hold an IEC 61439 or DIN 43671 certificate.

3.0255
Werkstoff number of the aluminium layer
2.0065
Werkstoff number of the copper layer
2.2
EN 10204 test report with every delivery
24h
to a quote, with the documents you need

Material standards and material numbers

CUPAL is not an alloy. Each layer keeps its own designation, and the certificate lists both. The Werkstoff numbers come from the German DIN 17007 numbering system, and the European designation of the aluminium is EN AW-1050A under EN 573-3. DIN 1787 (Kupfer – Halbzeug, 1973) is withdrawn, but older drawings and certificates still cite it.

LayerAluminium (carrier)
GradeAl 99.5 · EN AW-1050A
Werkstoff-Nr. (DIN 17007)3.0255
Puritymin. 99.5 % Al
Share of thickness70 %
LayerCopper (cladding)
GradeE1-Cu58
Werkstoff-Nr. (DIN 17007)2.0065
Purity99.9 % Cu
Share of thickness30 %

Which documents can you order with a delivery?

EN 10204 fixes only the type of document; the values on it come from the product specification named in the order. A 3.1 rests on inspection of the supplied lot before delivery, so request it with the order. Whether one can be supplied after delivery is confirmed case by case.

DocumentEN 10204 2.2 test report
What it showsCompliance with the order, with non-specific test results
Issued byThe manufacturer
Standard or on requestWith every delivery
Typically asked forGeneral industrial use, handover file
DocumentEN 10204 3.1 inspection certificate
What it showsResults measured on the supplied lot
Issued byThe manufacturer's inspection representative, independent of production
Standard or on requestOn request, with the order
Typically asked forPublic tenders, project acceptance, lot-level audits
DocumentISO 9001:2015 certificate, copy
What it showsThe supplier's (c:met GmbH) quality management system, not the material
Issued byCertification body, issued to c:met GmbH
Standard or on requestOn request, with the quote
Typically asked forSupplier approval, tenders
DocumentREACH SVHC declaration
What it showsNo SVHC above 0.1 % by weight
Issued byThe supplier (c:met GmbH)
Standard or on requestOn request, per delivery or project
Typically asked forCE technical file, material declarations to OEMs

2.2 or 3.1?

All four EN 10204 types (2.1, 2.2, 3.1, 3.2) compared, and which projects call for which.

Certificates for cut-to-size parts

Cutting does not change the material, so a cut part carries the certificate of the base material. Under clause 6 of EN 10204, a company that processes material without changing the properties ordered passes the manufacturer's certificate on unaltered, and a copy may show the partial quantity actually delivered. CUPAL parts cut or punched to your drawing therefore ship with the same 2.2 as a full sheet.

If the cut parts need a 3.1, say so in the quote request and send the drawing (DXF or PDF), the quantity and the sheet thickness. You get a quote within 24 hours; production of custom parts takes 5–10 working days.

ISO 9001:2015 in the supply chain

Our CUPAL material comes from c:met GmbH in Wendelstein, Germany, the CUPAL trademark holder, whose quality management system is certified to ISO 9001:2015. The certificate covers how c:met GmbH works, not the properties of the material; those are documented on the EN 10204 certificate. One does not replace the other, and tenders and supplier approvals often ask for both.

We send a copy of the certificate with the quote on request. If your own quality system requires supplier approval, list the documents you need in the quote request.

RoHS, REACH and SVHC

Both CUPAL layers are unalloyed, high-purity metals (Al min. 99.5 %, Cu 99.9 %) with no restricted substance added. RoHS and REACH answer different questions, so keep them apart in your compliance file.

RoHS

Directive 2011/65/EU

Applies to electrical and electronic equipment and restricts ten substances (lead, mercury, cadmium, hexavalent chromium, PBB, PBDE and four phthalates). A CUPAL sheet is not equipment but one of its materials, so RoHS does not apply to it directly; the maker of the finished equipment declares compliance.

REACH

SVHCs in articles

If an article contains a Candidate List SVHC above 0.1 % by weight, the supplier must inform the customer. CUPAL contains no SVHC above that threshold.

SVHC

Declaration on request

The supplier (c:met GmbH) issues the SVHC declaration per delivery or per project. It cites the Candidate List as of the date of issue and the two material numbers (3.0255, 2.0065). Ask for it for a CE technical file, a material declaration to an OEM (for example IPC-1752A) or a BOM audit.

Standards for the application

The standards below do not describe CUPAL as a material. They cover the equipment or joint it goes into. No material can be certified to IEC 61439 or DIN 43671: the maker of the finished assembly verifies its conformity, and a CUPAL washer or transition plate is one component in it.

Where it goes in practice: into switchgear and distribution boards, copper-aluminium busbar joints, between a cable lug and an aluminium busbar and into lightning protection systems.

DIN 43671

Copper busbars, design for continuous current

Gives the permissible continuous current of copper busbars by cross-section (1975 edition). Copper only.

DIN 43670

Aluminium busbars, design for continuous current

The aluminium counterpart of DIN 43671 (1975 edition). In a copper-aluminium busbar joint, the CUPAL transition piece is sized to the two bars it connects.

DIN 43670-2

Copper-clad aluminium busbars

Aluminium bus bars, copper cladding; design for continuous current (1985). A related field, not a CUPAL standard: there the copper surrounds the aluminium, while CUPAL is copper on one face and aluminium on the other.

EN 61439

Low-voltage switchgear and controlgear assemblies

The European edition of IEC 61439. It sets design and verification requirements for the assembly, and the assembly manufacturer verifies conformity. In a Cu/Al joint the CUPAL washer or transition plate is a component.

IEC 61238-1-1

Compression and mechanical connectors for power cables

Test methods and requirements up to 1 kV, with heat cycling, short-circuit and mechanical tests. It applies to the cable lug or connector, not to CUPAL as a material. The 2018 edition replaced IEC 61238-1:2003.

EN 62305

Protection against lightning

Requirements for the lightning protection of buildings and structures. Where a copper and an aluminium conductor are joined, a CUPAL strip or transition piece separates the two metals. Outdoors the cut edge must be protected or covered, so ask us about the joint.

Frequently asked questions about CUPAL standards and certificates

No, and no material can. IEC 61439 applies to the finished switchgear assembly, whose maker verifies its conformity; DIN 43671 is the design standard for copper busbars. CUPAL is a component in these joints. The material itself is identified by the EN 10204 certificate and its two Werkstoff numbers, 3.0255 and 2.0065.
The aluminium layer is Al 99.5, EN AW-1050A, Werkstoff-Nr. 3.0255. The copper layer is E1-Cu58, Werkstoff-Nr. 2.0065, with 99.9 % copper. Both Werkstoff numbers come from the DIN 17007 numbering system, and both appear on the certificate.
DIN 1787 (Kupfer – Halbzeug, 1973) was the German standard for copper semi-finished products, and DIN Media lists it as withdrawn. Older drawings and certificates still cite it. It does not assign material numbers; Werkstoff numbers come from DIN 17007.
Yes. Cutting does not change the material, so CUPAL parts cut or punched to a drawing ship with the EN 10204 2.2 of the base material. If you need a 3.1, say so in the quote request, because a 3.1 rests on inspection of the lot before delivery.
Yes. We send a copy of the ISO 9001:2015 certificate of our supplier, c:met GmbH, with the quote on request. Mention in the quote request that you need it for a tender or a supplier approval.
RoHS applies to the finished electrical equipment, and a CUPAL sheet is one of its materials. Both layers are unalloyed, high-purity aluminium and copper with no restricted substance added. Under REACH, CUPAL contains no SVHC above 0.1 % by weight; the supplier (c:met GmbH) issues a declaration to that effect on request, per delivery or per project.
No. ISO 9001:2015 certifies the supplier's quality management system, while an EN 10204 certificate documents the material of a specific delivery. Every CUPAL delivery comes with an EN 10204 2.2 test report, and a lot-specific 3.1 inspection certificate is available on request.

Request a quote with the documents you need

Tell us the product, the size and the quantity, and which documents you need (2.2, 3.1, ISO copy, SVHC declaration). The quote comes back within 24 hours.