Frequently asked questions

Material, sizes, certificates, ordering and delivery: straight answers about CUPAL®

General

CUPAL (CU + AL) is a cold-roll-bonded copper-aluminium bimetal, 70% aluminium and 30% copper by layer thickness. It is not an alloy: each layer keeps its own properties, and the two cannot be separated. Its purpose is to prevent galvanic corrosion where copper and aluminium conductors meet in a bolted joint. What is CUPAL? Composition, manufacture, data →
Four thicknesses: 0.5, 1.0, 1.5 and 2.0 mm, in 500 × 500 mm sheets. The 0.5 and 1.0 mm sheets ship from stock; 1.5 and 2.0 mm are made to order. The 500 × 2000 mm standard sheet is available on quotation. CUPAL sheet: sizes and prices →
When you connect a copper cable lug to an aluminium busbar, or an aluminium lug to a copper terminal. In direct contact the two metals corrode galvanically: over time the joint loosens, contact resistance rises, and heating and failure follow. Each face of a CUPAL washer touches its own metal, so this corrosion does not start. CUPAL washers M6–M20: sizes and prices →
By making like metal touch like metal on both sides of the joint. The washer or transition plate sits between the copper and the aluminium, with the copper face against the copper and the silver face against the aluminium. The copper-aluminium boundary lies inside the plate and only reaches the surface at a cut edge, so outdoor or humid joints need that edge protected. Connecting copper to aluminium →
An EN 10204 2.2 test report is the manufacturer's statement that the product meets the order, with non-specific test results that are not tied to the delivered lot. It ships with every CUPAL delivery by default. A 3.1 inspection certificate carries values measured on the actual lot and is validated by an authorised inspection representative independent of production; it is available on request. A declaration of compliance without test results is type 2.1. Ask for 3.1 for audits, public procurement or stricter projects. EN 10204 material certificate: 2.2 vs 3.1 in detail →
The base material is classified by Werkstoff number: 3.0255 for the aluminium layer (DIN 17007) and 2.0065 for the copper layer (DIN 1787). Installation standards set requirements for the whole joint, not for the material: EN/IEC 61439-1 for low-voltage switchgear assemblies, EN/IEC 62305 for lightning protection and EN/IEC 61238-1 for cable connectors. Each EU country publishes them under its own prefix, such as BS EN or DIN EN. Standards and documents →
The aluminium layer is AL 99.5 / EN AW-1050A, Werkstoff-Nr. 3.0255 (DIN 17007). The copper layer is E1-Cu58 (99.9% Cu), Werkstoff-Nr. 2.0065 (DIN 1787). Both appear on the EN 10204 certificate. CUPAL technical datasheet →

Products

Five: mill finish (Walzblank, the standard), bright (Blank), brushed (Gebürstet), satin (Satiniert) and EDT (electrical discharge texture, isotropic surface). Standard orders ship in mill finish; the others are available on request.
Yes. The copper side can be soft-soldered and electroplated with standard processes, just like solid copper. Keep heat treatment below 260 °C and under 4 hours, otherwise the bond strength drops. Installation and processing guide →
The bond between the copper and aluminium layers holds 70–110 N/cm of strip width. The datasheet specifies this range; the bond is permanent and the layers cannot be separated. CUPAL technical datasheet →
Each face points to its own metal: the copper face to the copper, the silver face to the aluminium. With a copper lug on an aluminium bar the copper face points up; with an aluminium lug on a copper bar the same washer goes in the other way round. The two metals never touch directly; the transition sits in the internal diffusion layer of the CUPAL. CUPAL installation guide →

Ordering

One 500 × 500 mm sheet. Parts made to your drawing also start from one sheet of base material, and any number of parts can be cut from it. For washers we quote small quantities too; order quantity and pack size are confirmed in the quote. Get a Quote →
Stock items (0.5 and 1.0 mm sheet, washers): 2–10 working days from order to delivery. Made-to-order thicknesses and custom cutting: 5–10 working days of production; a custom order takes 2–4 weeks door to door within the EU. We confirm the exact date in the quote. Lead times and pickup →
Send us the shapes and dimensions as DXF, PDF or JPG, by email or with the quote form. Without a drawing, describe the dimensions or set the part up in the configurator. You get the quote within 24 hours on working days. Custom parts to your drawing →
DXF (AutoCAD), PDF (dimensioned drawing) and JPG/PNG (sketch with dimensions). DXF works best, but a hand sketch is fine as long as the dimensions are marked. Shape and size in the configurator →
Use the quote form (you can attach a drawing) or email iroda@hidramix.eu. You can also call +36 30 255 4310. We reply within 24 hours on working days. Get a Quote →

Shipping

Yes, to every EU country, on DAP terms (Incoterms 2020). Shipping costs depend on weight and destination, and the quote states the exact amount. Shipping options and pickup →

Have a question?

Email us, use the form or call. We reply within 24 hours on working days.