Knowledge base

Technical guides, application notes and answers about CUPAL®

What CUPAL is for, and where to start

CUPAL is a copper-aluminium bimetal: a copper layer cold-roll-bonded onto aluminium sheet, 70% aluminium and 30% copper by layer thickness. Placed in a bolted joint between copper and aluminium conductors as a washer, transition plate or strip, it prevents galvanic corrosion, because each face touches its own metal. Without it, moisture drives the contact resistance up until the joint runs hot and works loose. The articles here answer practical questions: which transition a given joint needs, how to choose a washer size and install it, when to ask for a 3.1 certificate, and whether laser cutting or punching suits a part made to your drawing. Material values come from the technical datasheet; sizes and prices are on the product pages.

Start here:

Guides

Laser cutting or punching? Custom CUPAL parts from a drawing: which process pays off when

A custom copper-aluminium part can be cut from CUPAL sheet in three ways: on a shear, by laser or with a punching tool. What decides between them, what is different with a bimetal, and what to put in your quote request to get an accurate price first time.

October 26, 2026Read the full article →
Comparison

Transition washer: toothed or bimetallic? How to tell which one your drawing means

Two physically different parts are sold as a transition washer: a toothed copper-alloy washer and a roll-bonded copper-aluminium bimetal disc. How to tell them apart, which suits which joint, and the 11 bimetal sizes from M6 to M20.

September 8, 2026Read the full article →
Guides

Connecting copper to aluminium: which part for which joint

Bimetal lug, Al/Cu splice, bimetallic washer or cut plate: which copper-to-aluminium connector fits each of five joints, in what size, with SKUs.

September 8, 2026Read the full article →
Guides

CUPAL part number cross-reference: which size matches your code?

Distributor codes (880111, ICALCU10CS, Cupal M 10 Al-Cu, VCUP2, 1053) and same-format parts from DEHN, nVent ERIFLEX, BTicino, Klauke and Helukabel, mapped to the CUPAL sizes we supply.

September 8, 2026Read the full article →
Standards

EN 10204 2.2 certificate meaning: 2.2 vs 3.1

EN 10204 type 2.2 is a generic test report, type 3.1 a lot-specific inspection certificate. What each means, when you need which, and how to request one.

May 13, 2026Read the full article →
Guides

CUPAL bimetal installation and processing guide

Fitting a CUPAL bimetal washer step by step: surface prep, which face goes where, torque and edge protection outdoors. Plus the 260 °C / 4 h processing limit.

April 10, 2026Read the full article →
Guides

Which CUPAL washer fits? Choosing a size from M6 to M20

The bolt sets the bore and the cable-lug palm sets the outer diameter. A selector table for CUPAL bimetallic washers M6–M20, 16–46 mm OD, 1–2 mm thick by size, plus which way round they go.

April 2, 2026Read the full article →
Material science

CUPAL technical datasheet: 70/30 copper-aluminium bimetal sheet

Datasheet for CUPAL 70/30 copper-aluminium bimetal sheet: stock formats, copper-layer thickness per gauge, 41.9 MS/m (about 72 % IACS), 4.6 g/cm³, material numbers, heat-treatment limit and certificates.

March 15, 2026Read the full article →
Material science

Can copper and aluminium touch? Galvanic corrosion

They can touch, but where moisture reaches the joint the aluminium corrodes: 0.55 V apart in practice. What fails, and the bimetal washer that stops it.

March 1, 2026Read the full article →
Material science

What is CUPAL? The copper-aluminium (Cu-Al) bimetal, explained

CUPAL is copper roll-bonded onto aluminium, 70/30 by layer thickness: one copper face, one aluminium face, for bolted copper-to-aluminium joints. 4.6 g/cm³, 41.9 MS/m.

February 15, 2026Read the full article →

Have a question?

Send us the joint, the size and the thickness, and we reply with a quote within 24 hours on working days.