Sailing yachts · Masts · Bonding and lightning paths

Copper cable on an aluminium mast: a lasting joint without galvanic corrosion

Copper bonding, earthing or lightning cable on an aluminium mast, mast step or busbar, from AWG

In short

A copper bonding, earthing or lightning conductor bolted straight to an aluminium mast forms a galvanic cell that salt spray and condensation drive hard. The aluminium corrodes and the joint becomes an insulator while still looking sound. A CUPAL® washer or cut plate puts aluminium against the mast and copper against the lug.

M6–M20
Washers, 11 sizes from stock
0.5–2.0mm
Plate thickness for parts cut to drawing
2–10working days
Stock washers, order to delivery
24h
Quote

What happens when you bolt copper cable to an aluminium mast

The mast is aluminium because it has to be light. The bonding, earthing or lightning conductor is copper because it has to conduct. Where the two meet under one bolt, a galvanic cell forms as soon as there is an electrolyte: salt spray, rain, condensation. Aluminium is the less noble metal, so the mast corrodes, not the cable. The galvanic corrosion guide explains the mechanism and the galvanic series.

What makes it dangerous rather than merely ugly is that the corrosion product, aluminium oxide, is an insulator. The joint stays mechanically tight and quietly stops conducting. On a lightning path that means the protection you believe you have is not there when it matters; on a bonding or DC negative circuit it shows up as drifting readings and intermittent faults.

Salt water speeds it up, which is why the damage shows after a single season at sea. On fresh water, on lakes and rivers, the process is slower, but the conditions are the same: the two metals touch, and rain, mist and condensation inside the boat keep the joint wet. It gets to the same place, only later.

What to put in the joint

A copper-aluminium bimetal transition: one piece of material with an aluminium face and a copper face, roll-bonded at the mill. It is not a coating and not a plating; the Cu/Al interface sits inside the part. Fitted correctly, the aluminium face goes against the mast and the copper face against the copper cable lug, so every contact is metal against its own metal and nothing drives the corrosion.

Two forms cover almost every mast joint:

  • CUPAL washer for a single bolted lug, M6 to M20, 1–2 mm thick depending on size, from stock. The outer diameter should cover the whole lug palm, not just the area round the bolt.
  • CUPAL plate cut to drawing where aluminium and copper meet over a larger face (a mast step plate, a chainplate landing, an aluminium busbar in the switch panel), or where the fitting has its own hole pattern. The plate is cut from 0.5–2.0 mm CUPAL sheet to your drawing; a mast step usually needs the thicker gauge, and we recommend one from the drawing.

Antioxidant paste slows the same reaction but leaves the galvanic couple in place and has to be re-applied. A stainless washer does not remove the couple either; it adds a third metal that is also cathodic to aluminium. The bimetal transition removes the cause, so the inspection becomes mainly mechanical: is the bolt still tight, is the joint still covered.

Fitting notes

  • Orientation matters. Aluminium face to the mast, copper face to the cable. Fitted the wrong way round you recreate exactly the dissimilar contact you set out to remove.
  • Clean both faces at assembly. Aluminium re-oxidises quickly, so clean just before you assemble. Keep oil and general-purpose grease off the contact faces; if you add a contact compound, use one made for aluminium joints. The sequence is in the CUPAL installation guide.
  • Protect the cut edge. Like metals meet on the faces of a washer or plate, but at the cut edge the Al/Cu bond line is exposed. Seal or cover a joint that sees spray or condensation, and if you are unsure, describe the situation and we will answer for that joint.
  • Cross-section, not just size. CUPAL conducts 41.9 m/(Ω·mm²), about 72 % of copper. On a bonding or lightning path that rarely matters, because the bolt and the fitting set the contact area; on a joint carrying working current, allow for it.
  • On a boat this is one part of a system. Bonding, lightning protection and galvanic isolation are separate problems that interact. A bimetal transition fixes the dissimilar-metal joint. It is not a galvanic isolator, and it does not replace anode protection or a properly designed ground path. We supply the material and its EN 10204 certificate, not vessel or class certification.

If your joint is not on a mast but at an aluminium cable end, an in-line cable joint or a busbar transition, connecting copper to aluminium names the part for each of the four cases. The building version of the same joint, an aluminium down-conductor on a copper earth, is on the lightning protection page.

Where the joint actually sits

Four places a copper conductor meets aluminium on a boat or a mast, and what each one needs.

01 / 04

Bonding or lightning cable to an aluminium mast

The problem you need to solve. A copper bonding conductor, often tinned, is bolted to a lug on the mast wall or at the mast step. Spray and condensate run down the mast and sit at exactly that bolt. Within a season or two the aluminium under the lug is powdery and the path resistance has climbed.

How CUPAL solves it. A CUPAL washer under the lug, aluminium face to the mast. For a heavy conductor, such as a 4/0 AWG lug, a plate cut to drawing spreads the contact over the whole lug palm instead of concentrating it at the bolt.

02 / 04

Mast step to the deck or keel bonding point

The problem you need to solve. A deck-stepped or keel-stepped mast lands on a plate that is bonded back to the common point with copper. The step is the wettest place on the rig, it collects everything that runs down the spar, and the joint is usually bolted once and then left for years.

How CUPAL solves it. A CUPAL plate cut from a drawing to the step footprint. The whole bearing face becomes a bimetal transition instead of a ring of oxide forming round each bolt. Seal or cover the edge of the plate.

03 / 04

Copper lug onto an aluminium busbar in the panel

The problem you need to solve. Distribution and battery switch panels mix copper cable lugs with aluminium bars. The cabin is humid, and at a high-current joint rising contact resistance means heat before it means a fault.

How CUPAL solves it. A CUPAL washer between lug and bar, copper face to the lug, chosen so the outer diameter covers the whole lug palm.

04 / 04

Antenna, radar or signal mast ashore

The problem you need to solve. The same joint without the boat: an aluminium mast, a copper earth conductor, and a coastal or industrial atmosphere. A lightning path that measures fine on the day it is installed and drifts out of specification without anyone re-testing it.

How CUPAL solves it. CUPAL strip or a cut plate where the down-conductor meets the earth conductor, under the tested clamp.

Compared to what is usually fitted

Four ways this joint gets made, and how each one ages in damp, salty air.

ApproachCopper lug bolted straight to aluminium
What it does to the coupleNothing; full Al/Cu couple
MaintenanceRegular dismantling, cleaning and re-making
How it agesVisible corrosion at sea within a season
ApproachAntioxidant or jointing paste
What it does to the coupleSlows the reaction; the couple remains
MaintenanceRegular inspection and re-application
How it agesExtends it, does not remove it
ApproachStainless washer between the two
What it does to the coupleAdds a third metal, also cathodic to aluminium
MaintenanceYearly dismantling and cleaning
How it agesDelays it
ApproachCUPAL bimetal washer or plate
What it does to the coupleRemoves the couple; each metal meets its own kind
MaintenanceMechanical check, plus a check that the edge is still covered
How it agesNo Al/Cu couple on the faces; the cut edge needs protection

What people ask us about this joint

It works, if you keep up the maintenance. In his 2024 article on lightning protection, Darrell Nicholson writes that a stainless steel washer between the copper cable's end fitting and the aluminium mast will at least retard the corrosion, and that the connection needs yearly examination, with disassembly and cleaning to keep it conductive. That is honest advice for a joint you can reach every year. Stainless is still cathodic to aluminium, so the couple is replaced by another one, and the yearly job stays. With a bimetal transition, aluminium meets aluminium and copper meets copper; you still check that the bolt is tight and the edge is covered.
No. Tinning protects the strands from moisture, which is why it is used on boats, but the joint is decided at the contact face. Tin is also more noble than aluminium, so a tinned copper lug on an aluminium mast is still a galvanic cell. What matters is what the aluminium actually touches.
Yes, if the joint gets wet. On fresh water the process runs more slowly than in salt water, but the conditions are the same: the two metals touch, and rain, mist or condensation provide the electrolyte. On a mast joint left alone for years, the slower process still ends in an insulating oxide layer.
Two numbers decide it. The bolt size gives the thread, M6 to M20 from stock; the lug palm gives the outer diameter. The washer has to cover the whole transition, not just the area round the bolt, so if the lug is wider than the washer you had in mind, step up an outer diameter or ask for a plate cut to drawing. Send us the bolt size and the conductor cross-section and we will tell you which one it is.
Aluminium face to the aluminium mast or bar, copper face to the copper lug. The copper face is reddish, the aluminium face silver. Fitted the wrong way round, you recreate the dissimilar contact.
Yes. Send a DXF, a PDF or a dimensioned sketch and we supply the part cut from 0.5–2.0 mm CUPAL sheet; a partner workshop does the cutting. The cut part ships with the same EN 10204 2.2 test report as stock material. Quote within 24 hours, production 5–10 working days, EU door to door 2–4 weeks. Custom cutting has a minimum of one 500 × 500 mm sheet.
Keep oil and general-purpose grease off the contact faces; if you want a compound on them, use one made for aluminium joints, as the CUPAL installation guide says. Do protect the outside of the finished joint from spray and condensation, especially the cut edge of the washer or plate, because the Al/Cu bond line is exposed there. If you are not sure how to cover it, tell us where the joint sits and we will suggest a way.
Both, because both are copper conductors terminating on aluminium. They differ in what failure costs you: a degraded bonding joint shows up as drifting readings and corrosion elsewhere in the system, while a degraded lightning path is invisible until the strike. If the joint is on a lightning path, say so when you ask, because it changes which thickness and contact area we recommend. The lightning path as a whole should be designed by a specialist.
Tell us what meets what, the bolt size, the conductor cross-section and how many you need; for a shape, send a drawing. A quote comes back within 24 hours. Stock washers arrive 2–10 working days after the order; anything cut to a drawing takes 5–10 working days in production.

Applicable standards for this field

ABYC E-11
ABYC TE-4
ISO 10133
ISO 13297
EN 62305-3

Ask an engineer

Application not listed? Describe it and we will advise.