CUPAL bimetal installation and processing guide
A CUPAL® washer goes between the lug and the bar with each face against its own metal: copper face to copper, aluminium face to aluminium. Clean both contact faces, tighten to the torque the equipment or bolt maker specifies, and protect the exposed rim in damp or outdoor joints. When processing, never exceed 260 °C for 4 hours.
Fitting a CUPAL washer, step by step
Step 1: Surface preparation
- Clean the contact faces of the aluminium busbar, the copper cable lug and the washer
- Remove dirt and the oxide layer. Aluminium re-forms its oxide film in air, so assemble soon after cleaning
- Keep oil and general-purpose grease off the contact faces. If you use a contact compound, use one made for aluminium joints: Hydro recommends an oxide-inhibiting compound on the cleaned faces of bolted aluminium-copper joints to keep moisture out. The compound protects the faces; it is the washer that removes the galvanic couple
Step 2: Checking the orientation
- Each face of the CUPAL washer goes against its own metal: the reddish copper face against the copper part, the light silver face against the aluminium
- A copper lug on an aluminium busbar: copper face toward the lug. An aluminium lug on a copper busbar: the same washer, turned over
- If the two faces cannot be told apart because of oxidation, light sanding settles it: the reddish face is copper, the light silver face is aluminium. If sanding reveals no copper face at all, the part in your hand is not a bimetal: toothed copper-alloy transition washers are sold under the same name, and they have no copper face to orient
Step 3: Assembly
- Place the CUPAL washer between the cable lug and the busbar. The lug palm must sit fully on the washer; if it is wider, choose a larger outer diameter or a part cut to the palm
- Tighten the bolt to the torque specified by the equipment or fastener manufacturer. CUPAL has no torque of its own, and the washer does not change the joint's torque requirement
- A disc spring (Belleville washer) under the nut helps keep the contact pressure constant; Hydro recommends spring elements of this kind for bolted aluminium-copper joints
Step 4: Edge protection in damp or outdoor joints
- At the rim of the washer, the copper-aluminium bond line reaches the surface. That is the one place where the two metals meet outside the material
- In outdoor, damp or salt-laden locations, protect or cover that edge. If you are unsure what the joint needs, tell us the conditions and we will advise before you order
Step 5: Inspection
- Check that no part of the copper palm reaches past the washer onto the aluminium, and that the washer sits within the bar's contact face
- Check the bolt torque
What we supply
We supply CUPAL as stock bimetallic washers, strip and sheet, and as parts cut, punched or drilled to your drawing. The cutting and punching are done by our processing partner; simple forming is possible by arrangement. Deep drawing, roll forming, plating and soldering are work for your own shop or a specialist. The material suits them, within the limits below. For parts to a drawing, see custom cutting.
Processing CUPAL yourself
Cold forming
CUPAL sheet can be cold-formed. Our technical datasheet lists bending, deep drawing, embossing, stretch forming, edge bending, profiling, beading, riveting and hemming. If the part will be bent or flanged close to a cut edge, say so in the quote request, because the condition of the edge then matters too.
Cutting, punching and drilling
- Shearing, laser cutting and punching all work. Shearing leaves a slight burr, laser-cut edges may need deburring, and punching leaves a burr on the exit side, so mark on the drawing which face may carry it
- A burr on a contact face stops the face seating flat: deburr contact faces before fitting
- Laser cutting or punching for custom CUPAL parts compares the processes by quantity and geometry
Soldering
- The copper face can be soft-soldered like pure copper, with standard solders and fluxes
- The aluminium face cannot be soldered with standard processes
- Keep the heat brief and local: the bond between the layers tolerates at most 260 °C for at most 4 hours (see below)
Plating
- The copper face can be plated with standard galvanic processes, as copper can
- The aluminium face is protected by its own natural oxide layer
Heat-treatment limit
CRITICAL LIMIT: CUPAL may be heat-treated at a maximum of 260 °C for no longer than 4 hours.
- Heat treatment within this limit relieves work hardening after cold forming
- Beyond it, the intermetallic layer at the copper-aluminium interface grows uncontrolled, the bond weakens and the material becomes brittle; the damage is irreversible
- The limit applies to heating the whole part for a sustained time. Brief, local heat, such as a laser cut, affects only a narrow band along the edge
Summary
- Each face to its own metal: copper to copper, aluminium to aluminium, the same washer for both directions
- Clean faces, the equipment's torque: CUPAL adds no torque figure of its own
- Protect the rim outdoors and in damp places, and ask us when unsure
- Max. 260 °C / 4 hours when processing: never exceed it
Questions about fitting or processing CUPAL? Send us the joint or the drawing and we answer within 24 hours.