CUPAL part number cross-reference: which size matches your code?
This page maps the designations that turn up on drawings, BOM lines and old purchase orders onto the CUPAL® sizes we supply: distributor codes such as 880111, ICALCU10CS, Cupal M 10 Al-Cu, VCUP2 and 1053, and parts from other brands with the same format, from DEHN, nVent ERIFLEX, BTicino, Klauke and Helukabel. Bore, outer diameter, thickness and our SKU sit on the same row. Net list prices are on the product pages, one link away.
In short
Distributor codes (880109–880112, Cupal M 10 Al-Cu, ICALCU10CS, VCUP1, VCUP2, 1053) and same-format parts from DEHN, nVent ERIFLEX, BTicino, Klauke and Helukabel, mapped to the CUPAL size we supply, with bore, outer diameter, thickness and SKU on one row. Matches are by dimensions only. Where we have no stock size, the row says so.
- M6–M20
- 11 stocked washer sizes
- 1–2mm
- Washer thickness
- 2–10working days
- Washer lead time
- 24h
- Quote turnaround
Same format from other brands: DEHN, nVent ERIFLEX, BTicino, Klauke, Helukabel
The parts below come from other manufacturers and have the same format as a CUPAL size we supply. They are matched by dimensions only, using each maker's own datasheet or catalogue. Same format is not the same construction: Klauke and Helukabel describe their discs as E-Al, copper-plated on one side, while CUPAL is copper roll-bonded onto aluminium, 70/30 by layer thickness. A row here does not make our part an approved replacement in a specification that names the other brand; if yours does, send it and we check it with you before you order.
| Other brand, part no. | Their published dimensions | Same format in CUPAL | Note |
|---|---|---|---|
| DEHN 562 440 (CUPAB 500X40X0.5) | Strip 500 × 40 × 0.5 mm, Al/Cu | CUPAL strip 500 × 40 × 0.5 mm, from stock | DEHN states no layer ratio |
| DEHN 562 460 (CUPAB 500X60X0.5) | Strip 500 × 60 × 0.5 mm, Al/Cu | CUPAL strip 500 × 60 × 0.5 mm, cut to order | 5–10 working days production |
| nVent ERIFLEX BMS500 (553090) | Plate 500 × 500 × 1 mm: 0.7 mm Al + 0.3 mm Cu | TCUP10 sheet 500 × 500 × 1.0 mm, from stock | Same nominal layer split, 0.70 / 0.30 mm |
| nVent ERIFLEX BMS100 (553080) | Plate 100 × 100 × 1 mm: 0.7 mm Al + 0.3 mm Cu | CUPAL plate 100 × 100 × 1.0 mm | Cut from 1.0 mm sheet |
| BTicino 030009 | CUPAL plate 60 × 60 mm, cast-resin transformer accessory | CUPAL plate 60 × 60 mm | BTicino gives no thickness: measure the old plate or ask the transformer maker |
| BTicino 030014 / 030008 / 030010 / 030011 / 030012 | Plates 40 × 40, 50 × 50, 80 × 80, 100 × 100, 120 × 120 mm | CUPAL plates in the same sizes | Thickness as above |
| Klauke CS615 | M6, bore 6.5, OD 15, 2 mm | M6, 6.4 / 16 mm, ICALCU6CS | Our OD is 1 mm larger |
| Klauke CS818 · Helukabel 906049 | M8, bore 8.5, OD 18; Klauke 2 mm, Helukabel 1 mm | M8, 8.4 / 18 mm, ICALCU8CS | Our thickness per part number is confirmed in the quote; against a 1 mm part, check the bolt length |
| Klauke CS1022 · Helukabel 906050 | M10, bore 11, OD 22, 2 mm | M10, 10.5 / 23 mm, ICALCU10CS | Our OD is 1 mm larger |
| Klauke CS1228 · Helukabel 906051 | M12, bore 13, OD 28, 2 mm | M12, 13 / 26 mm or 13 / 30 mm | The lug palm decides: 26 mm up to 240 mm², 30 mm up to 400 mm² |
| Klauke CS1428 · Helukabel 906052 | M14, bore 15, OD 28, 2 mm | No stock size | Cut to your drawing by our partner |
| Klauke CS1635 · Helukabel 906053 | M16, bore 17, OD 35, 2 mm | M16, 17 / 35 mm, ICALCU16CS | Same bore and outer diameter |
All dimensions in mm, as published by the manufacturers when we checked them in November 2026: DEHN 562 440, DEHN 562 460, nVent ERIFLEX BMS, BTicino 030009 and the BTicino cast-resin transformer catalogue, Klauke Cupal discs, Helukabel KAC-U.
Klauke and Helukabel restrict their discs to dry environments; Klauke also allows them with tinned aluminium lugs in humid ones. A CUPAL part has the same weak point at its cut edge, where the bond line is exposed: outdoors or in humid conditions, protect or cover the edge and ask us before you specify.
Washer part numbers: which CUPAL washer they match
The four-digit 880109 / 880110 / 880111 / 880112 family, the Cupal M 6/8/10/12 Al-Cu designations and the ICALCU10CS-style codes all describe the same class of part: a roll-bonded copper-aluminium disc that sits in a bolted joint so that each conductor touches only its own metal. The table maps each string to the size we stock, using our own dimensions rather than any third party's. One name does not belong in that family: where a drawing says only transition washer, it can also mean a profiled copper-alloy washer, which is copper alloy throughout. How a bimetallic washer differs from a toothed one settles which part the line item is asking for before you match a code to it.
Designations that appear on distributor listings and drawings, against the CUPAL washer we hold for each. Lead time 2–10 working days.
| Designation you have | Also appears as | Our bore / outer Ø / thickness | Our size | Our SKU |
|---|---|---|---|---|
| 880109 | Cupal M 6 Al-Cu | 6.4 / 16 / 2 mm | M6 | ICALCU6CS |
| 880110 | Cupal M 8 Al-Cu | 8.4 / 18 / 2 mm | M8 | ICALCU8CS |
| 880111 | Cupal M 10 Al-Cu · EAN 8591120057484 | 10.5 / 23 / 2 mm | M10 | ICALCU10CS |
| 880112 | Cupal M 12 Al-Cu | 13 / 26 or 30 / 2 mm | M12 or M12 (large) | ICALCU12CS2 / ICALCU12CS |
| ICALCU10CS | Mfr-Nr 180082 · EAN 8014212184290 | 10.5 / 23 / 2 mm | M10 | ICALCU10CS |
| ICALCU10CS2 | — | 10.5 / 26 / 2 mm | M10 (large) | ICALCU10CS2 |
| ICALCU12CS2 | — | 13 / 26 / 2 mm | M12 | ICALCU12CS2 |
| ICALCU12CS | — | 13 / 30 / 2 mm | M12 (large) | ICALCU12CS |
Confirm before ordering. The rows are mapped by bolt size and nearest outer diameter. The bolt sets the bore, but the lug palm sets the outer diameter, so check it against your lug first. 880112 is usually published at Ø28 mm, which falls between our M12 at 26 mm and our large M12 at 30 mm; the lug decides, and the threshold is the cross-section it is crimped onto: up to 240 mm² take the 26 mm (ICALCU12CS2), 240–400 mm² take the 30 mm (ICALCU12CS). Every dimension in the table is ours, and published figures for these designations disagree with each other; see check 3 below before you order to a drawing.
The distributor codes above stop at M12. Our range does not: the full washer range with net list prices runs to 11 stocked sizes, 16–46 mm outer diameter, for lugs up to 630 mm². The priced rows can be linked directly: ICALCU6CS, ICALCU8CS, ICALCU10CS, ICALCU10CS2, ICALCU12CS2 and ICALCU12CS. Every row there carries a quantity field that builds the enquiry for you.
Sheet part numbers: the VCUP and HI-CUP designations
VCUP1 and VCUP2 designate a 500 × 500 mm CUPAL sheet in 0.5 mm and 1.0 mm; the same two sheets circulate on Hungarian and German BOM lines as HI-CUP-0.5 and HI-CUP-1.0. That is the same sheet we supply as TCUP05 and TCUP10, orderable directly at the net list price shown on the product page. A sheet is a larger commitment than a washer, so confirm the thickness before you order.
Sheet designations against the CUPAL sheet we supply, with availability per 500 × 500 mm sheet. The 1.5 and 2.0 mm thicknesses have no distributor equivalent; they are ours, made to order.
| Designation you have | Also appears as | Size | Our SKU | Availability |
|---|---|---|---|---|
| VCUP1 | HI-CUP-0.5 | 500 × 500 × 0.5 mm | TCUP05 | In stock |
| VCUP2 | HI-CUP-1.0 | 500 × 500 × 1.0 mm | TCUP10 | In stock |
| — | — | 500 × 500 × 1.5 mm | TCUP15 | Made to order, 5–10 working days |
| — | — | 500 × 500 × 2.0 mm | TCUP20 | Made to order, 5–10 working days |
The material is 70 % aluminium (AL 99.5, Werkstoff-Nr. 3.0255) over 30 % copper (E1-Cu58, Werkstoff-Nr. 2.0065), bond strength 70–110 N/cm; the full figures are in the technical datasheet. Net list prices and quantity fields are on the product page: TCUP05 and TCUP10. The 500 × 2000 mm format and any other geometry are quoted within 24 hours rather than list-priced.
Strip part numbers, and where we cannot ship from stock
The J. Pröpster designation 1053 is a 500 × 40 mm bimetal strip, typically used for a lightning-protection transition; it also appears under distributor SKUs such as JPR1053. It is the one code on this page we cannot supply from stock. Our stock strip is 500 × 40 × 0.5 mm; 1053 is normally published at 0.8 mm.
| Designation | Published as | What we can supply |
|---|---|---|
| 1053 | 500 × 40 × 0.8 mm (0.5 mm also appears) | Not in 0.8 mm. The same width cut to order in 0.5 or 1.0 mm |
Two things follow. First, we have no 0.8 mm gauge: CUPAL sheet comes in 0.5, 1.0, 1.5 and 2.0 mm. If 0.5 or 1.0 mm suits the joint, our partner cuts the strip to order in the same 40 mm width: quote within 24 hours, 5–10 working days of production. In 0.5 mm, the 500 × 40 × 0.5 mm stock strip is the same size and ships from stock. Second, the published thickness for this code disagrees across sources: 0.5 mm and 0.8 mm both appear against it, and 0.5 against 0.8 is a 60 % difference in section, not a rounding error. Measure the part you already have, or send us the drawing, and we confirm the thickness before anything is cut.
Cable-lug part numbers: how to read an ICALCU code
There are 109 lug SKUs, so instead of listing them all, here is how to read your own code. A tubular lug is ICALCU<cross-section><bolt>, so ICALCU24016 is 240 mm² for an M16 bolt. An inline connector is ICALCU<Al><Cu>V: ICALCU1610V joins a 16 mm² aluminium conductor to a 10 mm² copper one, and connectors carry no bolt size at all. A pin lug is ICALCU<Al>B<pin Ø>V, so ICALCU95B12V is 95 mm² with a Ø12 mm copper pin. Tubular lugs cover 10–625 mm² with M8 to M20 bolt holes, to DIN 46329; inline connectors join Al 16–500 mm² to Cu 10–400 mm²; pin lugs stop at 300 mm² and Ø18 mm. Codes ending in CS are not lugs but washers; those are in the table further up. Decode the string, then find the row in the full ICALCU cable-lug range.
How to confirm it really is the same part
A matching code is a lead, not a confirmation. Four checks settle it, in this order.
1. Start with the bolt size
The bore has to match the bolt, and nothing else about the joint changes that. An M10 bolted joint takes an M10 washer, whatever the catalogue calls it. If your source publishes no bore at all (and many of the Hungarian listings carrying the four-digit codes publish no dimensions whatsoever), the M-size in the description is the only thing you can rely on from it.
2. Check the outer diameter against the lug palm
This is where two parts with the same M-size stop being interchangeable. The washer has to cover the whole contact face of the lug, not just the ring around the bolt, so measure the palm and pick the outer diameter that covers it. That is why 880112 maps to two of our SKUs: our M12 exists at 26 mm for lugs up to 240 mm² and at 30 mm for 240–400 mm². The full washer range lists the maximum lug cross-section against every outer diameter.
3. Treat the published dimensions as figures to confirm, not to assume
Our washers are 1–2 mm thick depending on the size, and we confirm the value per part number in the quote. Published figures for the same designation do not agree with one another. Against the M10 codes you will find both 10.5 mm and 11 mm bore, both Ø23 and Ø26 mm outer diameter, and both 1 mm and 2 mm thickness, including under the manufacturer number and EAN printed on the ICALCU10CS row above, which lead to listings giving 1 mm or 2 mm. Against the 1053 strip, both 0.5 mm and 0.8 mm appear. Every figure in the tables above is ours. If your drawing or your existing stock is specific, measure the part or send us the drawing, and we confirm against it before you order rather than after.
4. Decide what certificate you need
An EN 10204 2.2 material certificate ships with every order as standard, and 3.1 is available on request. If you are replacing a part originally bought elsewhere and the specification calls for documented material, ask for 3.1 when you request the quote. It has to be ordered with the goods; whether one can still be supplied after delivery is confirmed case by case. The difference between the two grades is set out in the EN 10204 material certificate article.
Can't find your part number? Send us the designation and the drawing, and we confirm within 24 hours which of our sizes matches it, or have it cut to size from your drawing if none does. Get in touch.