GuidesApril 2, 20269 min read

Which CUPAL washer fits? Choosing a size from M6 to M20

In short

Two things decide the CUPAL® washer size: the bolt (M6–M20) sets the bore, and the cable-lug palm sets the outer diameter. The washer should cover the lug's whole contact face; if the palm is wider, take the next larger diameter. There are 11 stock sizes, 16–46 mm outer diameter, 1–2 mm thick depending on size.

M6–M20
11 stock sizes
16–46mm
Outer diameter
1–2mm
Thickness
2–10working days
Delivery from stock

This guide helps you pick the right washer. Prices, stock and ordering are on the CUPAL bimetallic washer product page; in the size table below, every size links to its own row there.

Two things decide the size

1. The bolt sets the bore

The washer's inner diameter is a clearance hole for the bolt, so an M10 bolt takes an M10 washer. The bores are: M6 6.4 mm, M8 8.4 mm, M10 10.5 mm, M12 13 mm, M16 17 mm, M20 21 mm. If all you have is an old washer, measure its bore with a calliper and you have the bolt size.

2. The lug palm sets the outer diameter

One bolt size can take several outer diameters: 23 and 26 mm for M10; 26, 30 and 46 mm for M12; 35 and 46 mm for M16; 37 and 46 mm for M20. The washer should cover the whole contact face of the cable lug, because that face carries the current. If the palm overhangs the washer, the contact area shrinks. Larger conductors come with wider lug palms, so the cross-section is a good first guide. If the lug is to hand, measure the palm width as well and compare it with the outer diameter.

Size selector: by lug cross-section and bolt

The table gives the outer diameter, in mm, of the smallest stock washer for each bolt and lug cross-section. The limits come from the "Max. lug" column of the size table further down.

Lug cross-sectionM6M8M10M12M16M20
up to 120 mm²161823263537
150–240 mm²––23263537
300 mm²––26303537
400 mm²–––303537
500 mm²–––463537
630 mm²––––4646

A dash means there is no stock size for that bolt and cross-section; see plates and cut parts below. If the lug palm is wider than the diameter in the table, go one size up.

Four worked examples:

  • 95 mm² copper lug on an M10 bolt, on an aluminium busbar: M10, 23 mm.
  • 185 mm² lug on M12: M12, 26 mm; if the palm is wider than 26 mm, M12, 30 mm.
  • 300 mm² lug on M12: M12, 30 mm.
  • 630 mm² lug on M16: M16, 46 mm.

Full size table

All 11 sizes are stock items, delivered 2–10 working days from order. Click a size to jump to its row on the product page, where the price and the quantity selector are.

SizeBoreOuter ØThicknessMax. lug
M66.4 mm16 mm1–2 mm120 mm²
M88.4 mm18 mm1–2 mm120 mm²
M1010.5 mm23 mm1–2 mm240 mm²
M10 (large)10.5 mm26 mm1–2 mm300 mm²
M1213 mm26 mm1–2 mm240 mm²
M12 (large)13 mm30 mm1–2 mm400 mm²
M12 (extra)13 mm46 mm1–2 mm500 mm²
M1617 mm35 mm1–2 mm500 mm²
M16 (large)17 mm46 mm1–2 mm630 mm²
M2021 mm37 mm1–2 mm500 mm²
M20 (large)21 mm46 mm1–2 mm630 mm²

If your drawing carries a distributor code rather than a size (880111, VCUP2, ICALCU10CS), the CUPAL part number cross-reference maps it onto these sizes.

Which way round does it go?

The copper face always faces the copper part and the aluminium (silver) face the aluminium. A copper lug on an aluminium busbar: the aluminium face sits on the bar and the lug sits on the copper face. An aluminium lug on a copper bar: the same washer, the other way up. Fit it upside down and copper touches aluminium in the joint again, so the washer no longer protects it. The reason is explained in preventing galvanic corrosion.

What the washer is, and what it is not

A CUPAL washer is a disc of cold-roll-bonded, diffusion-welded copper-aluminium bimetal. The layers are 70 % aluminium and 30 % copper by layer thickness, which is about 59 % copper by mass. The copper-aluminium boundary sits inside the washer, so on both faces of the bolted joint like metal meets like metal.

Two parts have similar names and do something else:

  • The thermostat bimetal strip in thermostats and circuit-breaker thermal releases. It bends because its two metals expand differently with heat. A CUPAL washer does not move; it is an electrical transition element.
  • The toothed copper-alloy transition washer, whose teeth break through the aluminium oxide film when the bolt is tightened. It is sold for the same job but works on a different principle and is not a bimetal. The difference is set out in bimetallic vs toothed transition washer.

Material, certificate, standards

  • Material grades: the exact designations of the aluminium and copper layers are on the CUPAL technical datasheet.
  • Certificate: every delivery comes with an EN 10204 2.2 test report; a 3.1 inspection certificate is available on request. See EN 10204 material certificate: 2.2 or 3.1.
  • Standards: IEC 61238 (connectors for power cables) and IEC 61439 (low-voltage switchgear assemblies) apply to the joint and the equipment, not to the washer material. Overview: standards.

Fitting in brief

  1. Clean the contact faces of the lug, the busbar and the washer, removing dirt and the oxide layer.
  2. Orient the washer: copper to copper, aluminium to aluminium.
  3. Tighten the bolt to the torque the equipment manufacturer specifies.
  4. Keep oil and general-purpose grease off the contact faces; if you use a contact compound, use one made for aluminium joints.
  5. A spring washer can be used alongside the CUPAL washer to hold the joint pressure.

The full steps are in the CUPAL installation guide.

Outdoors and in humid places, take extra care. On the washer's two faces copper never meets aluminium, but around its rim the cut edge shows the boundary between the two metals. In an outdoor or damp joint that edge needs to be protected or covered. Ask us before you specify such a joint, and we will answer for that specific case.

No stock size that fits?

Need a different bore, a larger outer diameter, or a square or multi-hole transition plate? See CUPAL plates, or have the part cut to your drawing. Our partner cuts the parts from CUPAL sheet; the minimum is one 500 × 500 mm sheet of stock. Quote within 24 hours, production 5–10 working days.

Not sure which size?

Send us the bolt size, the lug cross-section, the palm width if you know it, and the quantity. Send it as a quote request and we reply within 24 hours with the size we recommend and a quote.

Frequently asked questions about CUPAL washer sizes

By the bolt and the lug palm. The bolt size sets the bore: an M10 bolt takes an M10 washer. The cable-lug palm sets the outer diameter: the washer should cover the lug's whole contact face. One bolt size can have several diameters, for example 26, 30 and 46 mm for M12; the selector table shows which one a given lug cross-section needs.
11 stock sizes from M6 to M20: bores of 6.4–21 mm, outer diameters of 16–46 mm, 1–2 mm thick depending on size. M10, M12, M16 and M20 also come with a larger outer diameter for lugs with a bigger cross-section. Prices and stock are on the CUPAL washer product page, size by size.
The bolt decides, not the current. An M6 bolt takes an M6 washer, which suits lugs up to 120 mm². An M12 bolt takes an M12 washer with an outer diameter of 26 mm (up to 240 mm²), 30 mm (up to 400 mm²) or 46 mm (up to 500 mm²), depending on the lug's cross-section.
Up to 500 mm²: 46 mm on an M12 bolt, 35 mm on M16, 37 mm on M20. For 630 mm² on M16 or M20, the 46 mm washer. If the lug palm is wider than that, there is no stock size: a CUPAL plate or a part cut to your drawing is the answer.
Neither on its own: one face of a CUPAL washer is copper, the other aluminium, and each faces its own metal. A copper lug on an aluminium busbar: aluminium face on the bar, copper face under the lug. An aluminium lug on a copper bar: the other way up. Fitted upside down, copper touches aluminium in the joint again.
Only with the edge protected. On the faces copper never meets aluminium, but the cut edge shows the boundary between the two metals, so in an outdoor or damp joint the edge needs to be protected or covered. Before you specify such a joint, send us its details; the fitting steps are in the CUPAL installation guide.
Not always. The name transition washer is used for the CUPAL bimetallic washer, but also for a toothed copper-alloy washer whose teeth break through the aluminium oxide film when the bolt is tightened. The two work differently. If a specification only says transition washer, check which one it means; the bimetallic vs toothed transition washer article helps.
No. The bimetal strip in thermostats and thermal switches bends with heat because its two metals expand differently. A CUPAL washer does not move: it is an electrical transition element that puts its copper face against copper and its aluminium face against aluminium. Same word, different function.
1–2 mm, depending on the size; we confirm the value per part number in the quote. If you are replacing a washer in an existing joint, measure the old part and allow for the difference in the bolt length.
No lubricant is needed for the transition. Keep oil and general-purpose grease off the contact faces; if you want extra protection against moisture, use a contact compound made for aluminium joints, as the CUPAL installation guide describes. A spring washer can be used alongside the CUPAL washer to hold the joint pressure. Tighten the bolt to the torque specified by the equipment manufacturer.

Have a question?

Email us or use the form: we reply within 24 hours on working days.

Get a Quote